Rabu, 25 Februari 2009

Data Recovery of Lost Data Using Get Data Back - Step By Step Guide To Data Recovery

Data Recovery of Lost Data Using Get Data Back - Step By Step Guide To Data Recovery

Hard disk crashed? or windows got corrupted and you are about to lose all your important data? Don’t worry, data recovery is really simple and easy just follow the steps.

Data Recovery Using GetDataBack:

Following is the guide to recover your data using the software Get Data Back:

First thing make sure that do not write anything anymore on the crashed drive/partition from which you want to recover the data! This is to make sure your lost data keep preserve and you do not overwrite on it because after a data loss or hard disk crash, your data is no longer protected by the Operating System anymore. The Operating System thinks that the space where your lost data is present is free and can be used again. So when you copy something on it or installation of programs, Internet surfing (which generates temporary files) and even booting from the drive can permanently overwrite your lost files.

I. Setup

I.I. Set up a Recovery Computer

How to set up a Recovery Computer?

Before you do anything else, do the following:

1.The drive is not the Master/Boot Drive( C Drive) from which you want to recover data.If it is so than remove it from the system and attach it to another computer as a slave/second drive.

2.If the drive with the lost data is a second or external drive (please see the chapter I.II.II. External
Drives) you may leave the setup as it is. Please jump to II.I. Install GetDataBack.

3.If your drive is a laptop or notebook drive, please go to section I.II Data Recovery from Notebook/Laptop Drive Laptop Drive.

I.II Data Recovery from Notebook/Laptop Drive

If you need to recover data from a Notebook or Laptop drive do the following:

1.Remove/Unplug the drive from the Laptop/Notebook and attach it Notebook-to-IDE-adaptor which you can get at any computer store for under $15. Jumper your drive as a slave and connect it via this adaptor to any Windows computer.

I.II.I Data Recovery From External Drives - Like USB or Backup Drives

External drives, like for example USB-Drives, can also be recovered with GetDataBack. However - scanning the drive for your data takes much longer time when performed through USB, especially when using USB1, the older version of USB. The scan can take up to ten times longer, so while scanning a 100GB drive normally takes about 2 hours, it can be up to 20 hours through USB. If at all possible, remove the drive from its casing and attach it directly to the IDE-cable of your computer. If you are afraid that unwrapping the drive is going to void its warranty, leave everything as it is and be patient.

II. Installation

II.I Installing GetDataBack

Now you are ready to Install GetDataBack and recover your data. Download GetDataBack from here. There are two versions: GetDataBack for FAT which recovers data from FAT-formatted drives, GetDataBack for NTFS which recovers data from NTFS-formatted drives. Confused about which formatted partition was your drive?

Here is a little help!

If after the scan in Step 2 of the software you don’t see any useful file system entries, simply start over and try the other version. Install GetDataBack on the Master/Boot (C:) drive of your Recovery Computer.

III. Running and Using GetDataBack

Start GetDataBack by clicking on Start>All Programs>GetDataBack.

The first screen will look like this:

III.I Intro Screen

The only decision you’ll have to make here is to pick one the data recovery scenarios. Read through the choices carefully and then choose the one that most applies to your situation. Don’t hesitate to go with the standard options if you’re not sure what happened to your drive. The standard options are the recommended settings for most recoveries and more often than not they will produce the optimal recovery results.

Press Next.

III.II Step 1 Select The Drive You Want to Recover Data From

It will look like this:

III.II.I Screen

On the left hand side of Select Drive Step you’ll get a list of all the drives that are accessible in your system. You will have to select your “crashed” drive from this list. If you attached the drive as a slave drive as explained above this will be the entry “2nd Hard Drive (HD129:)” or if you had more than one hard drive in the system already it could be the 3rd, 4th or so hard drive. It shouldn’t be “1st Hard Drive (HD128:) because that would mean the drive you want to recover the data from is still set up as the boot drive.

Select the drive you want to recover under Physical Drives. Choose the entry under Physical Drive over any ones under Logical Drives - this will usually yield the best result.
There is usually no need to change any options manually in the Options tab on the right hand side. Refrain from changing any settings in Partial Scan - this feature is for experts only and will not improve your recovery results.

Press Next.

III.II.III Scanning the Drive

GetDataBack will now scan your drive for every available information regarding the original file system. The scan will take some time, you should at least allow an hour of scanning for every 50 GB of drive capacity.However - if the scan takes much longer than this, there is something wrong. It is normal if the scan is not completed within a couple of hours.

There are the a couple of reasons why the scan can take very long:

1.Your drive has a physical problem. If the drive has a lot of bad sectors (damaged areas on the drive’s platters that cannot be read anymore) or is otherwise damaged, the scan can take really long if it’s ever going to finish.

2.You are scanning an external drive through the USB port. As we have already told you Scanning a drive through USB takes much longer than scanning a drive that is connected to the internal IDE-cable of your computer. In extreme cases the scan can take 10 times longer, especially when using USB1.

III.III Step 2 - Selecting The File System

In Step 2 you will see:

III.III.I Step 2 Screen

On the left hand side of the screen you will see a list of the possible file systems GetDataBack has found. Don’t confuse the file system entries with the list of files and folders you are hoping to recover - you will see those in Step 3 of the software.

Each entry represents a (possible) partition on the drive. If you had more than one partition on the drive which you need to recover (for example logical drives C:\ and D:\) you will probably have to go back and forth between Steps 2 and 3 and select the corresponding entries separately in order to recover all files. Please note: If you had both FAT and NTFS partitions that you need to recover on the drive, you will have to run both versions of GetDataBack, GetDataBack for FAT first and then GetDataBack for NTFS or vise versa.
The file system entries are constructed by file system information GetDataBack has collected during the scan and that the software will use to reconstruct the file system that was originally on the drive and holds the required information about the location and content of your files. By default the most accurate file system entry is automatically on top of the list, so for the moment don’t be too concerned about the other entries or the entries that you get when you expand the list by selecting “Show all”.

On the right a detailed description of the found file system is displayed. This information is primarily used by our tech support staff.

So select the first entry in the list and press Next.

III.III.II You See No entries in Step 2

If you do not see any entries in Step 2 this can be for the following reasons:

1.You didn’t select the whole physical drive in Step 1 of the software.
If you select only part of the drive, select only a partition or restrict the area to be scanned by doing only a partial scan, GetDataBack in some cases will not be able to reconstruct the original file system or will just not find enough information to rebuild any file system at all.

2.You are using the wrong version of the software.
GetDataBack comes in two versions. You need GetDataBack for FAT if the original file system, i.e. the file system that was on the drive when you lost your files, was FAT and GetDataBack for NTFS if the original file system was NTFS.

3.Your drive is physically damaged and GetDataBack is unable to read enough sectors on the drive to gather the required information. If you receive a lot of error messages during the scan or you already know that your drive has a physical problem.

III.IV. Step 3 - Recovery Tree

Step 3 should look like this:

III.IV.I Step 3 screen

The screen looks like Windows Explorer. On the left side of the screen you see a tree of recovered directories and folders and a folder called “Lost files” created by GetDataBack, containing the files without directory information.

When you open a folder on the left side, the files in this folder are displayed on the right side.
First have a look at the left side. Does the directory tree look familiar to you? Do you see the folders that were on the drive you want to recover the data from? Does it seem that the directory structure is complete for this partition?
Now open up a folder that interests you on the left side and look on the right side. Do you see the files that you expect to be in this folder? Do you see the correct file names and does it appear that the files are all there?
Now open up a few files in order to test them. The fact that you see the folders, files, file names, the right file size etc. is a good sign, but doesn’t necessarily mean that the file content is there and that those files will be usable. You will not be able to test huge files or files that need to be imported correctly into their native application, like for example Outlook PST-files. Select files that are easy to check - for example Word documents (*.doc), pictures (*.jpg), graphics (*.gif). Open these files by double-clicking them or by using the build-in file viewer (F3). Please note: To open files by double-clicking them (for example Word documents with MS Word) their associated application needs to be installed on the Recovery Computer.

Do the files open fine, meaning you can see the file content, the text, picture etc.?
If so, repeat the same process with a couple of more file in different folders. If all or at least the majority of files open okay, your recovery is looking good. In order to actually save your recovered files you will need to copy them off the “bad” drive to another location. This can be a location on the Recovery Computer’s Master drive, any other drive attached to this computer, a USB drive or you can copy the files to a network destination. Make sure this location has enough free space for all the files you need. Never copy the recovered files back to a location on the drive you just recovered them from (the “bad” drive), or you will overwrite them and they will be gone forever!

You may copy either selected files and folders by tagging them on the right side or the whole thing by selecting the top entry on the left side that says [FAT] or [NTFS]. Select the files/folders/volume you need and press the copy button or Recovery>Copy on the main menu.

Now copy over your files. As soon as the copy operation has completed (which can take quite some time depending on the amount of data and the speed of your computer or network connection), make sure that all the files you need arrived safely on the destination drive. Do not at this point recycle your “bad” drive or format it or reinstall a new operating system. Keep the drive in its current state until you’re absolutely sure that you salvaged all the data that you need. Only then you should you decide whether or not you want to rebuild the system on this drive (reformat it, reinstall Windows and your other programs etc., copy back the recovered data to this drive). Never reuse a drive that has any physical problems, any bad sectors or a drive where you’re not sure why the data on it became suddenly inaccessible.

How to Install Windows XP on SATA without a Floppy.


Hello,
The main big problem to start installing Windows XP on a new notebook is the SATA Hard Drive that comes with it has not built-in drivers, we have to add them via floppy, but in the most of cases, we won have a floppy able to mount into the laptop, so, what we do?

We have to integrated sata drivers into xp cd. Otherwise, our notebook could not recognize our hdd and we cant install xp.

What we need?

  1. 1pcs empty cd.
  2. Sata drivers. You can download it from here.(zip pass is "www.notebook.gen.tr")

    Note: If you will use windows xp 64 bit version you must download this. Sata drivers for windows xp 64bit.
  3. Microsoft .net framework. you can download it from here.
  4. A software which called Nlite. You can download nlite from here.

Please follow my instructions carefully.

  1. Download an unzip sata drivers a folder. (My folders name is sata drivers)nbsp;
  2. Create a folder somewhere on your hard drive to copy the windows source files into. I called mine XP_Source but you can use whatever name you prefer. Just make sure there is adequate space on your hard drive to hold the files.
  3. Copy the full content from the distribution cd into this folder
  4. Start nLite.
  5. Welcome screen shows you which version of nLite you are running and allows you to choose an alternate language.
    - To continue click on Next.

    sata driver integration an xp installation cd
  6. We must now direct nLite to the folder which contains the windows installation files.
    To do this Click on Browse. And choose Xp_Source folder. Click next

    sata driver integration an xp installation cd
  7. Click next without doing anythink.
  8. Chose driver and bootable ISO by mouse and click next.

    sata driver integration an xp installation cd
  9. Click insert gt; single driver and choose iaachi.inf from you sata driver folder.

    sata driver integration an xp installation cd
  10. Select all drivers with shift or ctrl button and click OK an Next.

    sata driver integration an xp installation cd
  11. You will show a message "Do yo want to start the process". Click Yes and wait.
  12. Click next.
  13. Mode: Direct burn , Label: write your own label , Burn speed: Write slowly 10x is enough. Then click next and finish.

    sata driver integration an xp installation cd

Hdd could not found, sata hdd driver, how to sata hdd; acer sata driver, hp sata driver, notebook sata driver, asus sata driver, dell sata driver

Selasa, 24 Februari 2009

Cara Mudah Membedakan Madu Asli dan Palsu

Pepatah mengatakan, Jika berteman dengan pandai besi, maka akan terpercik apinya, jika berteman dengan penjual minyak wangi, minimal akan mencium wanginya. Nah, kebetulan salah seorang teman saya ada yang membuka usaha menjual madu. Jadi minimal dia tahu ilmu, cara membedakan mana madu yang asli dan mana madu yang palsu.

Ada berbagai macam cara membedakan mana madu asli, mana madu palsu. Tapi cara-cara tersebut sangat susah. Nah cara yang dikasih teman saya ini cara yang paling mudah.

Tuangkan air putih (air jernih) dalam sebuah wadah. Piring atau mangkok. Sebaiknya yang tidak bergambar supaya hasilnya tampak jelas. Masukkan satu sendok makan madu ke dalam air tersebut. Goyang-goyangkan perlahan-lahan piring tempat di mana air dan madu ditampung, sehingga madu yang ada di dalamnya menyebar. Jika madu tersebut asli, akan terlihat benang-benang berwarna kuning yang bentuknya menyerupai sebuah sarang lebah (heksagonal), seperti gambar di samping. Subhanallah, sungguh ajaib.

Kalo madunya palsu, misal terbuat dari gula, tentu tidak akan membentuk sarang lebah.

Mungkin cara ini sudah kuno ya? Tapi saya baru tahu. :)

Senin, 23 Februari 2009

Turitorial Download Data

Suka kesel ga kalo mau download di rapidshare setelah download 1 x nunggunya lama banget nah buat yang suka kesel ni ada beberapa triks untuk ngakalin rapidshare dan mega upload.

  • Buat download file dari rapidshare yang mau download tanpa berenti coba test link ini rapidgrab.
  • nih buat ngakalin megaupload yg mesti abis slotnya,
    http:/www.guardster.com/subscription/proxy_free.php
masukkan link megauploadnya dan HAPUS semua centangnya,trus aggree... dah.. (dah tak coba bisa..) ga tahu nih bisa untuk rapid ga?coba aja...

ok d just share for all netter

sumber :
http://kaskus.us/showthread.php?t=655513

Cara Download Program Bajakan

Kadang-kadang kita pengen program bajakan yang kita pakai bisa dipake selamanya. selama ini si kalo nyari program bajakan saya ada 2 tempat, satu dari situs resminya yang kedua dari situs www.kaskus.us nah kalo yg repot kalo dapat dari situs resmi kadang-kadang kita harus nyari crack atau sn nya biasanya saya nyari di http://crackspider.net,dsb. Walhasil yang saya temukan disana adalah crack untuk software-software yang versinya biasanya lebih lama dari versi yang ada website resminya. Hal ini tentunya sangat merepotkan, karena crack yang kita dapat biasanya tidak berfungsi. Mau tidak mau harus menunggu beberapa bulan kemudian agar bisa dapat crack software yang kita inginkan, padahal butuhnya sekarang:(

Lama mencari akhirnya ketemu juga caranya, biar bisa download software+crack:D Bagi yang sudah tahu caranya gak usah dibaca aj yah…..

Anda tinggal masuk aja ke website berikut :
http://phazeddl.com —> disini anda tinggal masukkan key program yang anda cari, setelah itu langsung deh keluar hasilnya. Biasanya akan link ke forum2 luar, disana anda bisa copy paste link software yang diberikan.:D

http://forumw.org —-> kalo disni anda harus join jadi anggota forum, gratis kok!! Setelah anda bergabung tinggal search aja program yang diinginkan. Selain forumw website lain yang layak dikunjungi adalah http://sharestation.com

Sebelum masuk ke web diatas pastikan komputer anda terproteksi dgn antivirus:D Saya tidak bertanggung jawab akibat tulisan diatas. Ingat! Hormatilah jerih payah pembuat program, pembajakan merupakan tindakan kejahatan yang bertentangan dengan hukum!! So, biasakan menggunakan opensource.:)

Semoga bisa memberikan masukan buat yang ingin mencari program bajakan...

Cara Menampilkan Folder yang di Hidden oleh Virus


Berikut ini saya berikan tips untuk menampilkan folder yang di hidden oleh virus karena belakangan ini makin banyak virus baru yang cara menyerangnya dengan menghilangkan folder data. ini langkah-langkahnya :
  1. Buka Dos kalo di windows Xp dengan cara mengetik perintah CMD di Run yang ada pada start menu.
  2. Setelah masuk ke dos pindahkan drive anda ketempat flashdisk liat di my computer flashdisk anda dibaca di drive mana contoh nya ada digambar dibawah ini
  3. Ketik pada drive yang sudah kita pilih ketik attrib -s -h /s /d contoh anda bisa liat pada gambar dibawah juga.
  4. setelah selesai maka semua folder yang hilang akan muncul lagi dibawah ini adalah contoh gambarnya
  5. Finish semoga data anda selamat



keterangan :

-S : Untuk menghilangkan attrib tipe sistem file

-H : Untuk menghilangkan attrib tipe hidden file

/S : Untuk memproses seluruh folder dan sub folder

/D : Memproses folder

* : Semua file/folder yang terdapat di USB Flashdisk

Setelah file bisa ditampilkan, jangan lupa untuk menghapus semua file application virus yang berekstensi .exe


Trik Memperbaikin Windows Xp tanpa Instal ulang

1. Memperbaiki Instalasi (Repair Install)

Jika Windows XP Anda rusak (corrupted) dimana Anda tidak mempunyai sistem operasi lain untuk booting, Anda dapat melakukan perbaikan instalasi (Repair Install) yang bekerja sebagaimana setting (pengaturan) yang awal.

  • Pastikan Anda mempunyai kunci (key) Windows XP yang valid.
  • Keseluruhan proses akan memakan waktu kurang lebih 1/2 atau 1 jam, tergantung spek komputer Anda.
  • Jika Anda dimintai password administrator, sebaiknya Anda memilih opsi perbaikan (repair) yang kedua,bukan yang pertama.
  • Masukkan CD Windows XP Anda dan lakukan booting dari CD tersebut.
  • Ketika sudah muncul opsi perbaikan kedua R=Repair, tekan tombol R Ini akan memulai perbaikan.
  • Tekan tombol F8 untuk menyetujui proses selanjutnya "I Agree at the Licensing Agreement"
  • Tekan tombol R saat direktori tempat Windows XP Anda terinstal. Biasanya C:\WINDOWS Selanjutnya akan dilakukan pengecekan drive C: dan mulai menyalin file-file. Dan secara otomatis restart jika diperlukan. Biarkan CD Anda dalam drivenya.
  • Berikutnya Anda akan melihat sebuah gambar "progress bar" yang merupakan bagian dari perbaikan, dia nampak seperti instalasi XP normal biasanya, meliputi "Collecting Information, Dynamic Update, Preparing Installation, Installing Windows, Finalizing Installation".
  • Ketika ditanya, klik tombol Next
  • Ketika ditanya untuk memasukkan kunci, masukkan kunci (key) Windows XP Anda yang valid.
  • Normalnya Anda menginginkan tetap berada dalam nama Domain atau Workgroup yang sama.
  • Komputer akan restart.
  • Kemudian Anda akan mempunyai layar yang sama sebagaimana pengaktifan sistem ketika instalasi normal.
  • Register jika Anda menginginkannya (biasanya tidak diperlukan).
Selesai & Sekarang Anda bisa log in dengan account Anda yang sudah ada.



2. NTOSKRNL Rusak atau Hilang (Missing or Corrupt)

Jika Anda mendapati pesan error bahwa "NTOSKRNL not found" / NTOSKRNL tak ditemukan lakukan:
  • Masukkan CD Windows XP dan booting dari CD tersebut.
  • Pada saat muncul opsi R=Repair yang pertama, tekan tombol R.
  • Tekan angka sesuai dengan lokasi instalasi Windows yang ingin diperbaiki yang sesuai.
  • Biasanya #1
  • Pindahlah ke drive CD Drive Anda berada.
  • Tulis: CD i386
  • Tulis: expand ntkrnlmp.ex_ C:\Windows\System32\ntoskrnl.exe
  • Jika Windows XP Anda terinstal di tempat lain, maka ubahlah sesuai dengan lokasinya.
  • Keluarkan CD Anda dan ketikkan EXIT


3. HAL.DLL Rusak atau Hilang (Missing or Corrupt)

Jika Anda mendapatkan error berkenaan dengan rusak atau hilangnya file hal.dll, ada kemungkinan file BOOT.INI mengalami salah konfigurasi (misconfigured).

  • Masukkan CD Windows XP dan booting dari CD tersebut.
  • Pada saat muncul opsi R=Repair yang pertama, tekan tombol R.
  • Tekan angka sesuai dengan lokasi instalasi Windows yang ingin diperbaiki yang sesuai.
  • Biasanya #1
  • Tulis: bootcfg /list
  • Menampilkan isi/masukan pada file BOOT.INI saat ini
  • Tulis: bootcfg /rebuild
  • Memperbaiki konfigurasi dari file BOOT.INI
  • Keluarkan CD Anda dan ketikkan EXIT



4. Direktori \WINDOWS\SYSTEM32\CONFIG rusak atau hilang


Jika Anda mendapatkan error dengan tulisan:

"Windows could not start because the following files is missing or corrupt
\WINDOWS\SYSTEM32\CONFIG\SYSTEM or \WINDOWS\SYSTEM32\CONFIG\SOFTWARE"

  • Masukkan CD Windows XP dan booting dari CD tersebut.
  • Pada saat muncul opsi R=Repair yang pertama, tekan tombol R.
  • Tekan angka sesuai dengan lokasi instalasi Windows yang ingin diperbaiki yang sesuai.
  • Biasanya #1
  • Masukkan password administrator jika diperlukan.
  • Tulis: cd \windows\system32\config
  • Berikutnya tergantung di bagian mana letak terjadinya kerusakan:
  • Tulis: ren software software.rusak ATAU ren system system.rusak
  • Berikutnya lagi juga tergantung di bagian mana letak terjadinya kerusakan:
  • Tulis: copy \windows\repair\system
  • Tulis: copy \windows\repair\software
  • Keluarkan CD Anda dan ketikkan EXIT
5. NTLDR atau NTDETECT.COM tak ditemukan
(NTLDR or NTDETECT.COM Not Found)
  • Jika Anda mendapati error bahwa NTLDR tak ditemukan saat booting:
  1. Untuk partisi tipe FAT
  • Silakan Anda melakukan booting dari disket Win98 Anda dan salinlah file NTLDR atau NTDETECT.COM
  • Dari direktori i386 ke drive induk/akar (root) C:\
  1. Untuk Partisi NTFS
  • Pada saat muncul opsi R=Repair yang pertama, tekan tombol R.
  • Tekan angka sesuai dengan lokasi instalasi Windows yang ingin diperbaiki yang sesuai.
  • Biasanya #1
  • Masukkan password administrator jika diperlukan.
  • Masukkan perintah berikut, dimana X: adalah alamat drive dari CD ROM Anda (Sesuaikan!).
  • Tulis: COPY X:\i386\NTLDR C\:
  • Tulis: COPY X:\i386\NTDETECT.COM C:\
  • Keluarkan CD Anda dan ketikkan EXIT

Disalin dari Postingan Cyclan Di Kaskus.us Semoga dapat berguna bagi yang membacanya.

Mengenal Bunyi Beep Pada PC

Bila PC Anda tidak lagi bereaksi setelah dihidupkan selain mengeluarkan bunyi beep—ia sebenarnya ingin menunjukkan pesan kesalahan. Bagaimana menginterpretasikan sinyal-sinyal terpenting dari BIOS tersebut??? Kita kelompokkan bunyi beep tadi berdasarkan tipe bios yang dipakainya:

AMI-BIOS
1x: RAM rusak atau tidak terpasang dengan tepat.
6x: Kesalahan Gate A20 - biasanya menunjukkan keyboard yang rusak.
8x: Graphic card rusak atau tidak terpasang dengan tepat dalam slot.
11x: Checksum-Error. Periksalah baterai pada motherboard.

Award-BIOS
1x panjang: Kesalahan RAM, modul tidak duduk dengan tepat.
1x panjang, 2x pendek: Graphic card cacat atau rusak.
1x panjang, 3x pendek: Keyboard rusak atau tidak terpasang (mulai versi 4.5 signal ini menunjukkan kesalahan graphic card).
Tak terputus: RAM atau graphic card tidak ditemukan.

Phoenix-BIOS
1x-1x-4x: BIOS rusak.
1x-2x-1x: Motherboard rusak.
1x-3x-1x: Masalah RAM, modul tidak terpasang dengan baik.
3x-1x-1x: Motherboard rusak.
3x-3x-4x: Graphic card rusak atau tidak terpasang dengan baik.

Jadi, kalo lain kali komputer kamu mengeluarkan bunyi beep, tinggal cocokkan bios, dan pasti ketahuan bagian mana yang bermasalah.

Semoga bisa membantu selama perbaikan